Configuration Description Use File ROM RedBoot loaded from SPI NOR flash to SDRAM redboot_ROM.ecm redboot_ROM.bin For serial communications, all versions run with 8 bits, no parity, and 1 stop bit at 115200 baud. RedBoot also supports ethernet communication and flash management.

Jehangir alias Abbaji is a compassionate don of the underworld. I think the critics will rate Maqbool as above average while the review-writing and movie-talking public will rave about it. Maqbool movie with english subtitles.

Jul 06, 2013  GSMULTI SETUP_GSMULTI_V30.zip MTK Download Setting USB PortMapping Setup_1.7.zip GSMULTI_Ver20 Manual.pdf GSMULTI video guides KF600 KE520 KM500 KM900. OMAP Flash Installer OMAPFlashInstaller-4.10.zip The Following User Says Thank You to LBOZ_GSM For This Useful Post: repairs4you2.

Note that the use of the term ROM for the initial RedBoot configuration is a historical accident. RedBoot actually runs from SDRAM after being loaded there from NOR flash by the User Boot Loader. The use of ROM for this configuration is intended to indicate that it initializes the microprocessor and board peripherals, as opposed to the RAM configuration which assumes that this has already been done. Initial Installation The Zoom board comes with U-Boot installed by default. The booting mechanism is that the on-chip firmware loads a small User Boot Loader from the start of NOR flash which then loads U-Boot from later in the flash. Our strategy is to leave the User Boot Loader in place and replace U-Boot with RedBoot. To write RedBoot to the SPI NOR flash, there are two possibilities: either run a RAM-resident RedBoot using a JTAG emulator and use that to program RedBoot into the SPI NOR flash; or use a Serial Boot and Flash Utility for OMAP-L138.

The following section describes this process using the Ronetix PEEDI; other JTAG emulators will have similar steps. Note If the board has been supplied with a TI User Boot Loader (UBL) version prior to 1.65, then on startup the board may output a string on the serial port saying 'No magic number found'. Smartcut 35 crack key. Earlier Zoom boards were known to be supplied with version 1.30. In this situation you will need to locate the script flashimg.tcl in the misc subdirectory of the Zoom platform HAL (i.e. Packages/hal/arm/arm9/zoom_l138/ VERSION/misc/flashimg.tcl) along with the redboot_ROM.bin file in the loaders subdirectory of your eCosPro installation, and run the following command at a command prompt: flashimg.tcl -oldubl redboot_ROM.bin redboot-oldubl.img You can then follow the above instructions for installing RedBoot, but use redboot-oldubl.img in place of uses of redboot_ROM.img.

You will also need to perform this step on any ROM startup user applications to be programmed into Flash using a JTAG device and booted by UBL. Programming RedBoot into NOR flash using the TI Serial Boot and Flash utility Texas Instruments have made available a command-line Serial Boot and Flash Loading Utility for OMAP-L138. More information including download and usage instructions is available. With this utility, you can program a ROM startup version of RedBoot in raw binary format (a prebuilt version of which may be found at loaders/zoom_l138/redboot_ROM.bin within your eCos installation). On Windows, we advise running the utility from a Command Prompt, rather than from a Cygwin bash shell. Before running the utility, first you need to connect your PC to the board's serial port using a null-modem RS232 serial cable.

Secondly, (with the board powered off) you must set DIP switch bank S7 so that switches 7, and 8 are set to the ON position and the rest are set to the OFF position. If you wish to confirm the board is configured correctly, then you can start a terminal emulator application (such as Hyperterminal on some versions of Windows) and connect to the serial port at 115200 baud, 8-N-1 with no hardware flow control, then you should see a 'BOOTME' prompt when you power on the board. To program the redboot_ROM.bin image, change directory to the directory containing the UBL binary file (which is included with the Serial Boot and Flash utility download), copy the redboot_ROM.bin into that directory, and then run the utility as follows: sfh_OMAP-L138.exe -flash ubl_OMAPL138_SPI_MEM.bin redboot_ROM.bin -APPStartAddr 0xC0008040 -APPLoadAddr 0xC0008000 After successful completion, RedBoot will be resident in SPI NOR Flash.